Engineering driven façades. System-backed delivery.

Clarity Is Visibility
Home / All / Facade Knowledge / Vision Glass, Spandrel and Infill Options for Unitized Curtain Wall: What to Specify in Your RFQ

Vision Glass, Spandrel and Infill Options for Unitized Curtain Wall: What to Specify in Your RFQ

Nov 11,2026
UNITIZED CURTAIN WALL · GLASS SPECIFICATION

Vision Glass, Spandrel and Infill Options: What to Specify in Your RFQ

“Low-E insulating glass” is not a complete specification. Pane treatment, coating position, cavity, interlayer, spandrel construction and appearance approvals all change cost, weight, performance and lead time.

Short answer: define each facade zone by its vision-glass build-up, coating and heat treatment, spandrel or infill type, performance targets, and required samples or mockup. Let project engineering finalize thicknesses, but do not leave the commercial glass description open to interpretation.
Modern unitized curtain wall showing transparent vision glazing and opaque spandrel bands
01Vision glass
02Spandrel types
03Risk control
04RFQ schedule
01

Vision Glass: Define the Full IGU Build-Up

Vision glass in a unitized curtain wall is normally an insulating glass unit (IGU): two or three panes separated by sealed cavities. Because the panel is factory glazed—often with structural silicone at one or more edges—the IGU must suit the project performance targets, structural calculations, edge-seal design and fabrication process.

Build-upTypical make-upCommon application
Double-glazed IGULow-E outer pane + 12–16 mm air or argon cavity + monolithic inner paneCommercial towers in moderate climates
Laminated inner paneLow-E outer + cavity + laminated inner, for example 6 + 1.52 PVB + 6Guarding, acoustic control or post-breakage retention
Laminated outer paneLaminated outer + cavity + inner paneWhere falling-glass risk, geometry or safety analysis requires retention
Triple-glazed IGUThree panes, two cavities and one or two Low-E coatingsCold climates or demanding energy targets, subject to engineering and sourcing
Coating

Product, position and appearance

Low-E or solar-control coatings often sit on surface 2, but the selected product controls colour, reflectivity and solar performance.

Treatment

HS, tempered and heat soak

State the required treatment. Heat-soak testing for tempered glass should be priced only where specified and available from the selected processor.

Retention

Laminated or monolithic

Laminated glass can improve safety, acoustics and post-breakage retention, with consequences for weight and cost.

Edge

Spacer and secondary seal

Warm-edge spacers reduce edge losses; structural-glazing edges need a secondary seal compatible with the structural silicone.

Engineering rule: final pane thickness, heat treatment and interlayer selection must follow project-specific glass calculations, wind loads, building height, code, energy and acoustic requirements—not a generic table.
02

Spandrel and Infill Options Compared

The spandrel zone conceals slab edges, ceiling voids and services. In a unitized panel it is normally factory assembled with insulation and a metal back pan, while coordination must preserve space for slab-edge fire stopping installed under the responsible trade.

Close view of modern glass curtain wall panels and opaque facade zones
OptionHow it worksStrengthsWatch-outs
Ceramic frit glassCeramic enamel is fired onto the glass for full or partial coverage.Durable, permanent colour; can coordinate with vision-glass coating.May read differently from vision glass under changing daylight and viewing angles.
Back-painted / opacifier glassCompatible paint or silicone opacifier is applied behind the glass.Broad colour range; may be more economical than full frit.Coating, sealants and IGU edge materials must be compatible.
Shadow boxVision-type glass sits in front of a recessed insulated back pan.Creates visual depth and may give the closest transition to vision areas.Heat build-up, condensation, venting, drainage and material temperature limits require design.
Aluminum panelA solid aluminum panel replaces glass in the spandrel or accent zone.Robust, no glass-breakage risk; can match or contrast with framing.Material finish, flatness, joint alignment and differential appearance need coordination.

Stone or other dense infills may also be possible, but weight and attachment consequences make them less typical in unitized systems.

03

Five Problems to Resolve Before Fabrication

01

Spandrel does not match vision glass

Use the same outer glass and coating where appropriate, then approve large samples or a full-size visual mockup. A perfect match is rarely realistic because one zone is transparent and the other opaque.

02

Shadow box traps heat or moisture

Define the ventilation, pressure-equalization and drainage approach; select back-pan finishes, insulation and seals for expected cavity temperatures.

03

Glass weight is underestimated

Laminated and triple-glazed units can materially increase panel weight, affecting frame design, anchors, lifting and installation.

04

Bidders price different products

One bid may assume heat-strengthened glass while another uses tempered glass or a different laminated interlayer. A glass schedule closes the gap.

05

Coating changes arrive late

Coated glass can carry long processor lead times. Freeze colour and performance after sample or mockup approval—not after procurement starts.

Geometric glass and metal facade panels illustrating different infill zones
04

What to Put in the RFQ Glass Schedule

A one-page schedule for each facade zone is normally enough to make bids comparable. If performance targets are not yet final, say so and ask every bidder to show the proposed build-up and expected values.

ItemWhat to stateExample
Zone and locationElevations, floors and panel types coveredTypical tower floors; east and west elevations
Vision-glass build-upPane thickness and treatment, cavity width and gas, laminated interlayer6 HS Low-E + 12A + 6 + 1.52 PVB + 6 HS
CoatingProduct or performance class, surface position, colour and reflectivity intentNeutral Low-E on surface 2; low-reflectivity intent
Spandrel / infillFrit, back-painted, shadow box or metal panel; finish referenceCeramic frit, full coverage, visual coordination with vision glass
Back pan and insulationMaterial, finish, insulation type and thickness intentGalvanized-steel back pan with mineral wool
PerformanceThermal, solar, acoustic, structural and safety criteriaValues from code, energy model and facade specification
QualityHeat soak where applicable, visual-quality standard and distortion limitsHeat soak for specified tempered glass, subject to processor capability
Samples / mockupSizes, colour options and visual-mockup requirementsTwo 300 × 300 mm samples per glass type, if included in the offer
05

How FOWALL Supports Glass and Infill Decisions

FOWALL coordinates glass and spandrel selections with the unitized frame and factory-glazing process. The precise deliverables and sourcing options depend on the project specification, glass processor, approved quotation and contract.

Engineering

Project-specific thermal review

Thermal analysis can be prepared for the proposed frame, vision-glass and spandrel assembly at the agreed project stage.

Options

Glass and infill coordination

Ceramic frit, back-painted glass, shadow-box concepts, aluminum panels and triple glazing may be evaluated where compatible with design, processor capability and commercial scope.

Evidence

Reports and recorded QC

Applicable third-party reports, pre-shipment photos, videos and project QC records can support submittal and release review.

Approval

Samples and inspection

Glass or spandrel samples and factory inspection can be arranged when specified and included in the quotation.

Detailed modern glass facade illustrating panel rhythm and finish coordination

Review the system context on the Unitized Curtain Wall Systems page and the material framework under Materials & Systems. For a full inquiry package, use the checklist in How to Prepare a Unitized Curtain Wall RFQ. Aluminum infill options are introduced on the Aluminum Facade Panel page.

06

Frequently Asked Questions

What is spandrel glass in a curtain wall?

Spandrel glass is opaque glass used between floors to conceal slab edges, ceiling voids and services. Opacity may come from ceramic frit, paint or an opacifier; a shadow box or metal panel can also form the opaque zone.

What is a common vision-glass configuration for unitized curtain walls?

A double-glazed IGU with a Low-E coating is common, often using heat-strengthened glass. Laminated panes are added when safety, acoustic or retention criteria require them. The final build-up remains project specific.

Is shadow-box spandrel better than frit glass?

Not universally. A shadow box can create depth and improve the visual transition to vision glass, but it needs careful heat, moisture and drainage design. Frit is generally simpler and robust. Appearance, performance, cost and maintainability determine the choice.

Why might heat-strengthened glass be considered instead of tempered glass?

Heat-strengthened glass typically has lower residual stress and different breakage behaviour. Tempered glass provides higher strength and safety-glazing fragmentation where required, but specifications may call for heat-soak testing to reduce nickel-sulfide breakage risk. Code and engineering determine the treatment.

Can aluminum panels be used as spandrel infill?

Yes. Aluminum panels can create a robust opaque zone and either match or contrast with the framing. Their alloy, thickness, stiffening, finish, flatness and attachment must be coordinated with the unitized panel design.

How detailed should the glass description in an RFQ be?

Detailed enough that two bidders price the same product: pane thicknesses and treatment, interlayers, cavity and gas, coating product and surface, spandrel type, performance criteria and required samples or mockup.

SPECIFY BEFORE PRICING

Give Every Bidder the Same Glass Basis

Send FOWALL your elevations, glass schedule and performance requirements. We can review vision and spandrel build-ups, flag weight or appearance risks, and define the technical information needed for an aligned quotation.

Discuss Your Facade Specification